Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
How do you actually feel with regards to How to Install a Bathtub Yourself?
Setting up a bathtub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is readily obtainable, the job can relocate immediately; if you have to open up a wall to get rid of the old tub as well as place the new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to move out the old tub and also set in the brand-new one. See to it you have certified yourself for the job and also are comfortable trying it. Instead of working with a contractor to take over a halfway-completed project, it is much better to think about using one before you begin. Chances are you might require a specialist plumber to make tube links.
This write-up will certainly help you set up a brand-new tub in your washroom if you have actually already purchased a new bathtub and also don't need to transform the setup of your previous water pipes.
Your devices and product checklist ought to comprise the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of removing the existing taps can be rather troublesome due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipes have been removed, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making certain that the washers remain in location in between the tap as well as the sink. Protect the tap in position with the manufacturer offered backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical tap adapters. The previous type ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Utilizing both wood boards under its feet, put the tub in the needed setting. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bath tub up until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water and check all joints as well as new pipework for leakages and tighten them if necessary. Fill up the bathtub as well as likewise examine the overflow outlet and also the typical electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the producer's user's manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has actually been utilized at the very least once as this will certainly resolve it into its final placement.
Planning for the Installment
First of all, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps unit to stop strain on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its last position.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall between the bathroom as well as the tiling, resulting in complications with moisture and also feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as can sealing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bathtub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly readily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
As an enthusiastic person who reads on A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that segment was beneficial. I beg you take a moment to share this post if you appreciated it. I am grateful for your time. Please visit our blog back soon.
24/7 plumbing excellence. Report this page